[Poll] What’s your favorite brand of guitar?

[jtcnj]

I need to get my Silkyn repaired!

I just last week put a pair of Tung Sol 6L6GC STR power tubes in and re-biased, at 73/68% I think it was (my voltage across each side of the OT is not exactly the same. They are made for higher plate voltages. Caught a 10% discount email from Tube Depot.

With the O-netics replacement PT I have exactly the same plate voltages as with the original.
It is sounding really good on the clean channel, more chimey and articulate than the stock Sovteks, which are ok just not great.
I have not done the grit channel mods yet and the stock overdrive is clipped a bit too square waved / large grains grainy, almost Fuzz-like, even at low settings (but not full on fuzz).
Its good for a bit of gain, but not so much for the ACDC crunch.

Dano Daddy 'O on the clean channel gets my inner Aussie rocking.
The on board reverb is working real well now too with the lower value cathode resistor mod and a fresh 12at-7 at the reverb driver V3, I think it is.

its about all I been doing for the last week, and working on The Rover.
Was meaning to add a post in The Muse I Adorn but didnt snap a pic.

 

[67plexi]

 

[Chubbles]

I dig my Daddy O. It has 200 knobs. I thought I was the only one. There is a setting in the manual for Texas Blues. Awesomeness.

 

[eSGEe]

THANK YOU FOR POSTING!!!!!!!!!!!

 

[BlackSG91]

Paul Weed Smith all the way!

;>)/

 

[smitty_p]

No Fenson or Gibder?

 

[eSGEe]

CHIBSON.................................buwahahahahahah


its o.k. PEAVEY isnt listed either ------

 

[kevinpaul]

My lost years I must have been kept on a farm because I don't know most of these names.
Any way of the ones are starting to come back to me I can't spell. You want one and you and your monkey go into a bar to dance and make up your minds. I would go with the one I had fun buying.
I never needed to say one word and asked and sent every thing by email. The guy brought my Martin to the door and shook my paw then left. Slick as snot on a door knob.

 

[Catmandue]

What about............HARMONY!
View attachment 15611

OR uhm ......... GODIN!
View attachment 15612
OR --- or ---or ------
AGILE!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
View attachment 15614


I THINK ITS SAFE TO SAY THERE IS A LOT OF LOVE FOR A LOT OF GUITARS!!!!!!!!!!!!!!!!!!!!!

Does a Harmony amp count also? Bad ass amps they made between 1960 to 1964.

 

[Catmandue]

I voted Fender because I have more of that gear than Gibson. With me it is like 50/50 Gibson/Fender. I also mess with B.C. Rich and Danelectro I'm sure more but got brain stinker.

 

[anna]

I voted Fender because I have more of that gear than Gibson. With me it is like 50/50 Gibson/Fender. I also mess with B.C. Rich and Danelectro I'm sure more but got brain stinker.

Thanks for sharing your opinion!

 

[eSGEe]

I voted Gibson....more of them "G" things around here than anything ......once was a time NO G's where here just Epis and Squires ....flipper ferengi ......life is good

 

[Session 5]

I have to say these three View attachment 17907 View attachment 17907 [ 17907[/ATTACH]

 

[Session 5]

 

[ninjaking67]

Way to go, Session 5! Keepin' the Canadian economy rollin'!

 

[bea]

Neither. My favorite brand is DIY.
And, BTW, Harley Benton ist missing

Although i own 2 Gibsons and 3 Epiphones - a good custom guitar from a luthier should always be preferrable to a factory made guitar. Support Your local luthier!
And You can have a fine Instrument made from local woods...

 

[Session 5]

Way to go, Session 5! Keepin' the Canadian economy rollin'!

I just can't say enough about the Quality of these guitars .